基于plc控制的四段自動化傳輸線.doc
約27頁DOC格式手機打開展開
基于plc控制的四段自動化傳輸線,摘 要自動化傳輸線是工業生產過程中最常見的設備之一。自上個世紀60年代plc問世以來，由于其在控制方面的優點，目前利用plc作為核心控制器件的工業應用越來越廣泛，本論文對plc及其相關的外圍器件進行了研究，提出了基于plc的自動化傳輸線控制系統框架。 根據自動化傳輸線的運行要求，本論文設計了一種利用plc（松下fp1）...
內容介紹
此文檔由會員 有貨小二 發布
摘 要
自動化傳輸線是工業生產過程中最常見的設備之一。自上個世紀60年代PLC問世以來，由于其在控制方面的優點，目前利用PLC作為核心控制器件的工業應用越來越廣泛，本論文對PLC及其相關的外圍器件進行了研究，提出了基于PLC的自動化傳輸線控制系統框架。
根據自動化傳輸線的運行要求，本論文設計了一種利用PLC（松下FP1）作為主控器件，包含移載、頂升和提升三個基本環節的自動化傳輸控制系統。首先闡述了PLC及接近開關、行程開關等外圍器件的工作原理，然后介紹了自動化傳輸線各個部分的工作原理及整體框圖。在此基礎上，選擇出相應的硬件并簡單介紹其技術參數，根據其原理設計出自動化傳輸線的硬件控制框圖，并利用FPWIN-GR軟件編寫了相應的梯形圖程序。
通過實際調試運行，該系統運行穩定，安全可靠，取得了較好的效果，達到了實際運行要求。
關鍵詞：傳輸線,PLC,FP1,接近開關,行程開關, FPWIN-GR,梯形圖
ABSTRACT
Automation transmission line is in the industrial production process one of most common equipment. Since on century 60's PLC being published, as a result of it in the control aspect merit, has at present controlled the component using PLC as the core the industrial application to be more and more widespread, the present paper has conducted the research to PLC and the correlation periphery component, proposed based on the PLC automated transmission line control system frame.
According to the automated transmission line movement request, the present paper designed one kind using PLC (Panasonic FP1) to take the master control component, contained moves carries, goes against rises and promotes three basic links the automated transmission control systems. First elaborated periphery component and so on PLC and close switch, limit switch principles of work, then introduced the automated transmission line each part of principle of work and the overall diagram. In this foundation, choice showing off should the hardware and introduced simply its technical parameter, designs the automated transmission line according to its principle the hardware control diagram, and has compiled the corresponding
Trapezoidal chart procedure using the FPWIN-GR software.
Through the actual debugging movement, this system movement is stable, safe reliable, has obtained the good effect, has met
the actual movement requirements.
Key words: transmission line; PLC; FP1; close switch; limit switch; FPWIN-GR; trapezoidal chart
目 錄
1 緒論 6
1.1 概述 6
1.2課題來源和意義 6
1.3畢業設計的主要內容 7
2 基于PLC的自動化傳輸線工作原理 8
2.1.1 PLC工作原理 8
2.1.2 PLC的組成 10
2.1.3 PLC的I/O處理過程 11
2.1.4 PLC的工作過程 11
2.1.5松下FP1簡介 12
2.2外圍器件的工作原理 12
2.2.1接近開關 12
2.2.2行程開關 13
2.2.3常見控制按鈕 13
2.3傳輸線基本環節的工作原理 2.3.1移載部分 14
2.3.2頂升部分 14
2.3.3提升部分 14
3 自動化傳輸系統的設計 15
3.1.1 柜子原理圖IO點 16
3.1.2 自動化傳輸線的整體框架 17
3.1.3 系統硬件框圖柜子原理圖 19
3.2系統軟件設計 20
3.2.1 FPWIN-GR簡介 20
3.2.2 傳輸線梯形圖（見附錄） 22
參考文獻 22
致謝 22
自動化傳輸線是工業生產過程中最常見的設備之一。自上個世紀60年代PLC問世以來，由于其在控制方面的優點，目前利用PLC作為核心控制器件的工業應用越來越廣泛，本論文對PLC及其相關的外圍器件進行了研究，提出了基于PLC的自動化傳輸線控制系統框架。
根據自動化傳輸線的運行要求，本論文設計了一種利用PLC（松下FP1）作為主控器件，包含移載、頂升和提升三個基本環節的自動化傳輸控制系統。首先闡述了PLC及接近開關、行程開關等外圍器件的工作原理，然后介紹了自動化傳輸線各個部分的工作原理及整體框圖。在此基礎上，選擇出相應的硬件并簡單介紹其技術參數，根據其原理設計出自動化傳輸線的硬件控制框圖，并利用FPWIN-GR軟件編寫了相應的梯形圖程序。
通過實際調試運行，該系統運行穩定，安全可靠，取得了較好的效果，達到了實際運行要求。
關鍵詞：傳輸線,PLC,FP1,接近開關,行程開關, FPWIN-GR,梯形圖
ABSTRACT
Automation transmission line is in the industrial production process one of most common equipment. Since on century 60's PLC being published, as a result of it in the control aspect merit, has at present controlled the component using PLC as the core the industrial application to be more and more widespread, the present paper has conducted the research to PLC and the correlation periphery component, proposed based on the PLC automated transmission line control system frame.
According to the automated transmission line movement request, the present paper designed one kind using PLC (Panasonic FP1) to take the master control component, contained moves carries, goes against rises and promotes three basic links the automated transmission control systems. First elaborated periphery component and so on PLC and close switch, limit switch principles of work, then introduced the automated transmission line each part of principle of work and the overall diagram. In this foundation, choice showing off should the hardware and introduced simply its technical parameter, designs the automated transmission line according to its principle the hardware control diagram, and has compiled the corresponding
Trapezoidal chart procedure using the FPWIN-GR software.
Through the actual debugging movement, this system movement is stable, safe reliable, has obtained the good effect, has met
the actual movement requirements.
Key words: transmission line; PLC; FP1; close switch; limit switch; FPWIN-GR; trapezoidal chart
目 錄
1 緒論 6
1.1 概述 6
1.2課題來源和意義 6
1.3畢業設計的主要內容 7
2 基于PLC的自動化傳輸線工作原理 8
2.1.1 PLC工作原理 8
2.1.2 PLC的組成 10
2.1.3 PLC的I/O處理過程 11
2.1.4 PLC的工作過程 11
2.1.5松下FP1簡介 12
2.2外圍器件的工作原理 12
2.2.1接近開關 12
2.2.2行程開關 13
2.2.3常見控制按鈕 13
2.3傳輸線基本環節的工作原理 2.3.1移載部分 14
2.3.2頂升部分 14
2.3.3提升部分 14
3 自動化傳輸系統的設計 15
3.1.1 柜子原理圖IO點 16
3.1.2 自動化傳輸線的整體框架 17
3.1.3 系統硬件框圖柜子原理圖 19
3.2系統軟件設計 20
3.2.1 FPWIN-GR簡介 20
3.2.2 傳輸線梯形圖（見附錄） 22
參考文獻 22
致謝 22
