C6132普通車床主傳動系統設計說明書


摘要

主傳動系統設計是機床設計中非常重要的組成部分，本次設計主要由機床的級數入手，于結構式、結構網擬定，再到齒輪和軸的設計，再選擇各種主傳動配合件，對軸和齒輪及配合件進行校核，將主傳動方案“結構化”，設計主軸變速箱裝配圖及零件圖，側重進行傳動軸組件、主軸組件、變速機構、箱體、潤滑與密封、傳動軸及滑移齒輪零件的設計，完成設計任務。
本次突出了結構設計的要求，在保證機床的基本要求下，根據機床設計的原則，擬定機構式和結構網，對機床的機構進行精簡，力求降低生產成本；主軸和齒輪設計在滿足強度需要的同時，材料的選擇也是采用折中的原則，沒有選擇過高強度的材料從而造成浪費。
【關鍵詞】車床、主傳動系統、結構式、電動機。

Abstract
    Main drive system design is Very important part of the Machine Design,The design of the series to start primarily by machine,In the structure, the structure network developed, to the design of gears and shafts,Choose a variety of main drive with the pieces of the shaft and gear, and checked with the parts ，design and motive of completion sport spread the lord to move the project"the structure turn" , Design a principal axis to become soon a box assemble diagram and spare parts diagram and lay particular emphasis on to carry on spread to move stalk module, principal axis module and become soon organization, box a body, lubricate and seal completely, spread to move stalk and slippery move wheel gear spare parts of design to complete design tasks.
This highlights the structural design requirements,under the basic requirements for ensuring the machine ,According to the principles of machine tool design,Development of institutional and structural net,Streamlining of the machine tool sector,Strive to reduce production costs,No choice of materials resulting in high strength waste.

【Keywords】lather, Main drive system,Structure , Electric motor.
 

目錄
   緒論 1
1.主軸極限轉速的確定 2
2.  主動參數的擬定 3
2.1確定傳動公比 3
2.2主電動機的選擇 4
3.普通車床的規格 5
4.變速結構的設計 5
4.1確定變速組及各變速組中變速副的數目 5
4.2結構式的擬定 5
4.3結構網的擬定 8
4.4各變速組的變速范圍及極限傳動比 9
4.5確定各軸的轉速 9
4.6繪制轉速圖 10
4.7確定各變速組變速副齒數 10
4.8繪制變速系統圖 12
5.傳動件的設計 13
5.1帶輪的設計 13
5.2傳動軸的直徑估算 16
5.3確定各軸轉速 16
5.4傳動軸直徑的估算：確定各軸最小直徑 17
5.5鍵的選擇、傳動軸、鍵的校核 18
6.各變速組齒輪模數的確定和校核 20
6.1齒輪模數的確定： 20
6.2齒輪的設計 24
7.齒輪校驗 26
7.1齒輪強度校核 26
7.1.1校核a組齒輪 26
7.1.2 校核b組齒輪 28
7.1.3 校核c組齒輪 29
8.主軸組件設計 31
8.1主軸的基本尺寸確定 31
8.1.1外徑尺寸D 31
8.1.2主軸孔徑d 31
8.1.3主軸懸伸量a 33
8.1.4支撐跨距L 33
8.1.5主軸最佳跨距的確定 33
8.2主軸剛度驗算 35
8.3主軸剛度驗算 36
8.4各軸軸承的選用的型號 38
謝辭 38
小結 38
參考文獻 39