太陽能冷熱暖三聯供熱泵機組.doc
約83頁DOC格式手機打開展開
太陽能冷熱暖三聯供熱泵機組,摘 要太陽能熱泵系統是一種可以實現夏季制冷、冬季制熱并同時提供全年生活熱水的技術，該技術由于最大限度地利用太陽能光熱及空氣源低品位熱源，系統cop系數大幅度提高，解決了室外換熱器翅片冬季低溫條件下表面結霜問題。此項技術可以將技術趨于成熟、商品化程度很高的熱泵節能技術與太陽能熱利用技術有機地結合起來，彌補了兩者單獨工作時...
內容介紹
此文檔由會員 違規屏蔽12 發布
摘 要
太陽能熱泵系統是一種可以實現夏季制冷、冬季制熱并同時提供全年生活熱水的技術，該技術由于最大限度地利用太陽能光熱及空氣源低品位熱源，系統COP系數大幅度提高，解決了室外換熱器翅片冬季低溫條件下表面結霜問題。此項技術可以將技術趨于成熟、商品化程度很高的熱泵節能技術與太陽能熱利用技術有機地結合起來，彌補了兩者單獨工作時的不足，具有結構緊湊、形式多樣、運行可靠、節能明顯、壽命長等優點。因此，本文提出了一種新型的太陽能冷熱暖三聯供熱泵機組，基于該機組的工作特點，開發一套監控系統，用以實現上述三種工況的轉換，實驗數據的采集、顯示、存儲等。
首先，本文給出了新型太陽能冷熱暖三聯供熱泵系統的組成和工作原理，然后在此基礎上，根據系統的檢測與控制要求，設計了比較適宜的監控方案，監控系統主要由人機界面、PLC、檢測系統組成。接著，詳細介紹了系統的熱物理參數（溫度、壓力）的檢測原理與儀器選型方案，闡述了系統控制方案、壓縮機能量調節方案、人機界面和PLC的選型方案，最后對所選的觸摸屏和PLC進行相應的程序編寫。觸摸屏不僅用以實現工況選擇、溫度壓力的數據實時顯示、實時曲線顯示、歷史記錄等，而且作為監控系統的核心，分析判斷從系統中采集到的參數數據，再將控制信號傳遞給PLC，由PLC驅動各開關、設備執行動作，完成一套完整的控制路線。
本文采用和利時的可編程控制器PLC與昆侖通態MCGS組態軟件嵌入式觸摸屏構建一套監控系統，對太陽能冷熱暖三聯供熱泵系統進行監控，經過系統的運行與實驗監測的結果表明該監控系統對此熱泵機組的監控效果良好，說明監控系統設計的合理性，為本課題后續進一步研究奠定了研究基礎。
關鍵詞 太陽能熱泵；監控；PLC；MCGS組態軟件
Abstract
Solar assisted heat pump is a system that can not only be used as refrigeration and heating, but also supply with life heat water. Because of this technology makes use of solar energy and air heat source maximum, COP coefficient rises dramatically and solving the frost of surface of heat exchange fans in air oil pipe outdoors. This technology can combine heat pump energy-saving which is driving to mature and high commercial degree with solar energy. It offsets the shortage of both heat pump energy-saving and solar energy. And it has merit of compact configuration, multi-form, credible circulation, distinct energy-saving, long life and so on. So, in view of the above questions, this article put forward a new unit of solar assisted heat pump system with the function of cooling, heating and gaining hot water. This article aimed at the character of the system explores a set of monitored control system. The system can carry out three-operating mode switch and collection, show and memory of experiment data.
First, this article provides the composition and working principle of the system, then according to system’s monitored control and control request on the basis of operating principle of the system, presents monitor scheme. The control system is made up of human-machine interface, PLC and detection system. Then, the article introduces in detail the principle of thermophysical parameters (temperature, pressure) and the lectotype scheme of the instruments. And it also presents control scheme of the system, compressor’s energy regulation scheme, the lectotype scheme of human-machine interface and PLC. Finally, do the program of the touch screen and PLC. The touch screen not only realizes operating mode choose, setting value input, real-time digital display of temperature and pressure, real-time curve display, history record, but also analysis the data detected from the system then send the message to PLC, PLC drive each switch, equipment to execute action, this complete a set of complete control line.
This paper adopts HeLiShi PLC and KunLunTongTai MCGS software to construct a set of monitoring system to monitor the system of solar assisted heat pump system with cooling, heating and gaining hot water, According to the experiment results, the monitoring system design is rational and further research of this task can be established.
Keywords Solar assisted heat pump; monitor; PLC; MCGS configuration software
目 錄
摘 要 I
Abstract III
第1章 緒論 1
1.1 課題研究背景 1
1.2 國內外研究現狀 2
1.2.1 國內的研究現狀與趨勢 2
1.2.2 國外的研究現狀與趨勢 3
1.3 本文的主要研究工作 4
第2章 太陽能冷熱暖三聯供熱泵系統的工作原理 6
2.1 熱泵概述 6
2.1.1 熱泵發展概述 6
2.1.2 熱泵技術原理 7
2.1.3 熱泵機組控制系統概述 7
2.2 太陽能熱泵概述 9
2.2.1 太陽能熱泵工作原理 9
2.2.2 太陽能熱泵發展趨勢 10
2.2.3 新型太陽能熱泵系統的提出 11
2.3 太陽能冷熱暖三聯供熱泵系統的原理 11
2.3.1 系統組成 11
2.3.2 系統各部分功能 12
2.3.3 系統工作原理 13
2.4 本章小結 17
第3章 太陽能冷熱暖三聯供熱泵系統的監控方案設計 18
3.1 監控系統技術功能背景 18
3.1.1 太陽能冷熱暖三聯供熱泵監控系統概述 18
3.1.2 監控系統設計依據 18
3.2 太陽能熱泵監控系統的基本結構與工作原理 18
3.2.1 太陽能熱泵監控系統的基本結構 18
3.2.2 監控方..
太陽能熱泵系統是一種可以實現夏季制冷、冬季制熱并同時提供全年生活熱水的技術，該技術由于最大限度地利用太陽能光熱及空氣源低品位熱源，系統COP系數大幅度提高，解決了室外換熱器翅片冬季低溫條件下表面結霜問題。此項技術可以將技術趨于成熟、商品化程度很高的熱泵節能技術與太陽能熱利用技術有機地結合起來，彌補了兩者單獨工作時的不足，具有結構緊湊、形式多樣、運行可靠、節能明顯、壽命長等優點。因此，本文提出了一種新型的太陽能冷熱暖三聯供熱泵機組，基于該機組的工作特點，開發一套監控系統，用以實現上述三種工況的轉換，實驗數據的采集、顯示、存儲等。
首先，本文給出了新型太陽能冷熱暖三聯供熱泵系統的組成和工作原理，然后在此基礎上，根據系統的檢測與控制要求，設計了比較適宜的監控方案，監控系統主要由人機界面、PLC、檢測系統組成。接著，詳細介紹了系統的熱物理參數（溫度、壓力）的檢測原理與儀器選型方案，闡述了系統控制方案、壓縮機能量調節方案、人機界面和PLC的選型方案，最后對所選的觸摸屏和PLC進行相應的程序編寫。觸摸屏不僅用以實現工況選擇、溫度壓力的數據實時顯示、實時曲線顯示、歷史記錄等，而且作為監控系統的核心，分析判斷從系統中采集到的參數數據，再將控制信號傳遞給PLC，由PLC驅動各開關、設備執行動作，完成一套完整的控制路線。
本文采用和利時的可編程控制器PLC與昆侖通態MCGS組態軟件嵌入式觸摸屏構建一套監控系統，對太陽能冷熱暖三聯供熱泵系統進行監控，經過系統的運行與實驗監測的結果表明該監控系統對此熱泵機組的監控效果良好，說明監控系統設計的合理性，為本課題后續進一步研究奠定了研究基礎。
關鍵詞 太陽能熱泵；監控；PLC；MCGS組態軟件
Abstract
Solar assisted heat pump is a system that can not only be used as refrigeration and heating, but also supply with life heat water. Because of this technology makes use of solar energy and air heat source maximum, COP coefficient rises dramatically and solving the frost of surface of heat exchange fans in air oil pipe outdoors. This technology can combine heat pump energy-saving which is driving to mature and high commercial degree with solar energy. It offsets the shortage of both heat pump energy-saving and solar energy. And it has merit of compact configuration, multi-form, credible circulation, distinct energy-saving, long life and so on. So, in view of the above questions, this article put forward a new unit of solar assisted heat pump system with the function of cooling, heating and gaining hot water. This article aimed at the character of the system explores a set of monitored control system. The system can carry out three-operating mode switch and collection, show and memory of experiment data.
First, this article provides the composition and working principle of the system, then according to system’s monitored control and control request on the basis of operating principle of the system, presents monitor scheme. The control system is made up of human-machine interface, PLC and detection system. Then, the article introduces in detail the principle of thermophysical parameters (temperature, pressure) and the lectotype scheme of the instruments. And it also presents control scheme of the system, compressor’s energy regulation scheme, the lectotype scheme of human-machine interface and PLC. Finally, do the program of the touch screen and PLC. The touch screen not only realizes operating mode choose, setting value input, real-time digital display of temperature and pressure, real-time curve display, history record, but also analysis the data detected from the system then send the message to PLC, PLC drive each switch, equipment to execute action, this complete a set of complete control line.
This paper adopts HeLiShi PLC and KunLunTongTai MCGS software to construct a set of monitoring system to monitor the system of solar assisted heat pump system with cooling, heating and gaining hot water, According to the experiment results, the monitoring system design is rational and further research of this task can be established.
Keywords Solar assisted heat pump; monitor; PLC; MCGS configuration software
目 錄
摘 要 I
Abstract III
第1章 緒論 1
1.1 課題研究背景 1
1.2 國內外研究現狀 2
1.2.1 國內的研究現狀與趨勢 2
1.2.2 國外的研究現狀與趨勢 3
1.3 本文的主要研究工作 4
第2章 太陽能冷熱暖三聯供熱泵系統的工作原理 6
2.1 熱泵概述 6
2.1.1 熱泵發展概述 6
2.1.2 熱泵技術原理 7
2.1.3 熱泵機組控制系統概述 7
2.2 太陽能熱泵概述 9
2.2.1 太陽能熱泵工作原理 9
2.2.2 太陽能熱泵發展趨勢 10
2.2.3 新型太陽能熱泵系統的提出 11
2.3 太陽能冷熱暖三聯供熱泵系統的原理 11
2.3.1 系統組成 11
2.3.2 系統各部分功能 12
2.3.3 系統工作原理 13
2.4 本章小結 17
第3章 太陽能冷熱暖三聯供熱泵系統的監控方案設計 18
3.1 監控系統技術功能背景 18
3.1.1 太陽能冷熱暖三聯供熱泵監控系統概述 18
3.1.2 監控系統設計依據 18
3.2 太陽能熱泵監控系統的基本結構與工作原理 18
3.2.1 太陽能熱泵監控系統的基本結構 18
3.2.2 監控方..
