《畢業論文-電視臺嘉賓滅燈系統的設計》.pdf
約47頁PDF格式手機打開展開
《畢業論文-電視臺嘉賓滅燈系統的設計》,摘 要 “南寧電視臺嘉賓滅燈系統”題目來自于南寧電視臺項目部?其參照目標為江蘇衛視“非誠勿擾”節目的女嘉賓滅燈控制系統?但在其中提出了更高的要求?同時實現50位以上女嘉賓現場參與節目?江蘇衛視為24位?。受控?zé)舯K數量的增加使得在通常的控制系統中面臨如下幾大難點? 1、整體通信控制距離大大加長? 2、整體通信系統負載過大...
內容介紹
此文檔由會員 ucanhui 發布
摘 要 “南寧電視臺嘉賓滅燈系統”題目來自于南寧電視臺項目部?其參照目標為江蘇衛視“非
誠勿擾”節目的女嘉賓滅燈控制系統?但在其中提出了更高的要求?同時實現50位以上女嘉
賓現場參與節目?江蘇衛視為24位?。受控?zé)舯K數量的增加使得在通常的控制系統中面臨如
下幾大難點?
1、整體通信控制距離大大加長?
2、整體通信系統負載過大?
3、受控終端數量較大且需實現可調。
針對這幾個問題?本設計擬使用RS485通信方式、可選5-15V通信電壓、從機自身硬件
設置地址的方式解決此類矛盾。初步預定本系統可使最多255個終端工作點分布在一條長達
2Km以上的總線上同時工作。
宏觀上講?本系統采用MCS-51內核的STC12C5A60S2和STC89C52RC兩款單片機分別作為
本系統的主機和從機核心處理芯片?構成一個由下位主機控制流程執行、下位從機負責終端
執行、上位機負責初始參數配置啟動指令下達和滅燈結果輸出顯示等功能的復合型多機通信
協同處理工作系統。
本文將在江蘇衛視“非誠勿擾”滅燈控制系統中已實現的功能之上?針對新項目涉及的
以上幾大難點?從一個在校大學生的角度、嚴格按照工程開發實踐要求、詳細探討實際項目
的開發流程及其關鍵技術資料的錄入?為以后的在校大學生師弟師妹們實際工程項目的開發
奠定一些薄弱的實際項目開發基礎。
關鍵詞?單片機 上、下位機 串行通信 RS485通信
Abstract The title of "guests’ lighting-off system in Nanning TV " derives from the project department
of Nanning TV Station, which refers to the female guests’ lighting-off system in a program of “If
You Are the One” in Jiangsu Satellite TV. However, this thesis puts forward a higher requirement:
making 50 or more female guests on-site participation in the program (there are 24 women on-set at
present in Jiangsu Satellite TV). The increase in the number of controlled lights may cause several
problems if it is under the usual system.
1, the overall communication control gap is much longer;
2, the overall communication system load will be too large;
3, the number of controlled terminals will increase and adjustability is required.
As to these questions, this design will employ the RS485 communication, 5 ~ 15V voltage and
its own hardware address set to resolve such conflicts. Initially, this system is scheduled to utilize
255 terminal points distributed in a more then 2Km bus and make them work simultaneously.
From the macro perspective, the system is going to use the STC12C5A60S2 and
STC89C52RC of MCS-51 core chip as the master and slave core processing chip respectively,
aiming to form a mixed multi-machine system allowing multi-machines to co-process. In this
system, a lower host controls the execution; the hypogyny slave is responsible for the
implementation of the terminal; the epigyny is responsible for sending down the initial parameter
configuration directives and the output manifestation of lighting-off.
This thesis, based on the previous functions, will strictly conform to the practical requirements
for engineering development, and explicitly explore the development procedures of the practical
project and the login of its key technological information from a university student’s perspective. It
is hoped that this article will lay certain foundation in practical exploitation for teachers and
students in university.
Key words: single-chip, the upper and lower machine, serial communication, RS485
communication
目 錄
摘 要........................................................................................................................................1
目 錄.........................................................................................................................................I
插圖索引目錄........................................................................................................................ IV
表格索引目錄........................................................................................................................ IV
第一章 項目概述..................................................................................................................1
1.1 項目概述..................................................................................................................1
1.2 項目目標..................................................................................................................1
1.3 涉及關鍵技術...........................................................................................................1
第二章 總體方案設計................................................................................
誠勿擾”節目的女嘉賓滅燈控制系統?但在其中提出了更高的要求?同時實現50位以上女嘉
賓現場參與節目?江蘇衛視為24位?。受控?zé)舯K數量的增加使得在通常的控制系統中面臨如
下幾大難點?
1、整體通信控制距離大大加長?
2、整體通信系統負載過大?
3、受控終端數量較大且需實現可調。
針對這幾個問題?本設計擬使用RS485通信方式、可選5-15V通信電壓、從機自身硬件
設置地址的方式解決此類矛盾。初步預定本系統可使最多255個終端工作點分布在一條長達
2Km以上的總線上同時工作。
宏觀上講?本系統采用MCS-51內核的STC12C5A60S2和STC89C52RC兩款單片機分別作為
本系統的主機和從機核心處理芯片?構成一個由下位主機控制流程執行、下位從機負責終端
執行、上位機負責初始參數配置啟動指令下達和滅燈結果輸出顯示等功能的復合型多機通信
協同處理工作系統。
本文將在江蘇衛視“非誠勿擾”滅燈控制系統中已實現的功能之上?針對新項目涉及的
以上幾大難點?從一個在校大學生的角度、嚴格按照工程開發實踐要求、詳細探討實際項目
的開發流程及其關鍵技術資料的錄入?為以后的在校大學生師弟師妹們實際工程項目的開發
奠定一些薄弱的實際項目開發基礎。
關鍵詞?單片機 上、下位機 串行通信 RS485通信
Abstract The title of "guests’ lighting-off system in Nanning TV " derives from the project department
of Nanning TV Station, which refers to the female guests’ lighting-off system in a program of “If
You Are the One” in Jiangsu Satellite TV. However, this thesis puts forward a higher requirement:
making 50 or more female guests on-site participation in the program (there are 24 women on-set at
present in Jiangsu Satellite TV). The increase in the number of controlled lights may cause several
problems if it is under the usual system.
1, the overall communication control gap is much longer;
2, the overall communication system load will be too large;
3, the number of controlled terminals will increase and adjustability is required.
As to these questions, this design will employ the RS485 communication, 5 ~ 15V voltage and
its own hardware address set to resolve such conflicts. Initially, this system is scheduled to utilize
255 terminal points distributed in a more then 2Km bus and make them work simultaneously.
From the macro perspective, the system is going to use the STC12C5A60S2 and
STC89C52RC of MCS-51 core chip as the master and slave core processing chip respectively,
aiming to form a mixed multi-machine system allowing multi-machines to co-process. In this
system, a lower host controls the execution; the hypogyny slave is responsible for the
implementation of the terminal; the epigyny is responsible for sending down the initial parameter
configuration directives and the output manifestation of lighting-off.
This thesis, based on the previous functions, will strictly conform to the practical requirements
for engineering development, and explicitly explore the development procedures of the practical
project and the login of its key technological information from a university student’s perspective. It
is hoped that this article will lay certain foundation in practical exploitation for teachers and
students in university.
Key words: single-chip, the upper and lower machine, serial communication, RS485
communication
目 錄
摘 要........................................................................................................................................1
目 錄.........................................................................................................................................I
插圖索引目錄........................................................................................................................ IV
表格索引目錄........................................................................................................................ IV
第一章 項目概述..................................................................................................................1
1.1 項目概述..................................................................................................................1
1.2 項目目標..................................................................................................................1
1.3 涉及關鍵技術...........................................................................................................1
第二章 總體方案設計................................................................................
