論文標準WORD格式排版 32頁 附總裝圖—01—0#.dwg 裝配圖AO.dwg 裝配圖中間軸A2.dwg 部件圖—02—剪切機構0#.dwg 機蓋.dwg 機座A1.dwg 零件圖—03—大齒輪2#.dwg

摘要
擺動剪切機是安裝在型鋼熱連機前，用于切頭切尾和卡鋼事故的處理剪。隨著國民經濟的發展，對型鋼產品數量的要求更高。本設計為型鋼設計切頭的擺動剪，設計中對擺動剪的局部做了改進。
首先，本文討論了型鋼軋機在國民經濟中的地位，并對300/500機組平面布置示意圖的概況進行了整體的介紹。并介紹了擺動剪的結構特點和研究的內容與方法。根據現有設備狀況，對設備生產中存在的問題進行分析，對主要部件結構做了合理的選用。然后，根據機組原始參數初選主電機容量，對其進行發熱校核和過載校核，對主要零件進行強度校核。對齒輪做了強度計算，對曲軸計算了彎曲應力，彎扭合成應力；校核了危險斷面；以及滑塊損壞的改進設計及潤滑方法，簡單計算擺動剪的可靠性和經濟評價。
通過以上工作，擺動剪切機在使用壽命、產品質量理論上應該有一定的提高。設計內容有實際價值。該擺動剪作為加熱爐前的方坯切頭飛剪。

關鍵詞：剪切機，擺動，主傳動

A Design of Swing Scissors
Abstract
Swing scissors is installed before the sharp steel of hot continuous rolling mills, which is used to cut the head and end of the steel and deal with the jamming of the steels.With the development of the national economy, the request of the sharp steels’s quality is higher than before. In the thesis, the cutting of the head of the swing scissors is researched, and makes some improvments of partial strcture.
First, the thesis has discussed the position of the rolling mill of sharp steel in the national economy, and makes the general instruction for 300/500 unit plane arrangement. Next, introducing the structural characteristic of the swing cutting and the method and content of the research .According to exising equipment condition, analysing the exist problem in equipment production, the strcture of the major parts are reasonable to choosed. Then,according to the primitive parameter of the unit, I primarily choose the capacity of the main motor, and make the heat examination and overload examination, choose if satisfying the requirement, otherwise choose again until the examination is satisfyed. I make the strength examination for major element. As to gears, I make the strength calulation; as to crank, I caculated the curving stress and the crooked synthesis stress, examinationing the dangerous cross section, as well as the improment of the damages of the slide and the method of lubrication. Finally I caculated the economy appraisal and the reliablity of swing scissors.
Through the work of this thesis, swing scissors should certain raise in service life and product quality theoretically, but need the unceasing improvement in practice.

Key-word: scissors, swing, main drive


目錄
1 緒論 1
1.1 課題選擇的背景和目的 1
1.2 熱軋型鋼軋機的國內外發展趨勢 1
1.2.1 軋機布置向半連續化或全連續化發展 2
1.2.2 軋制工藝改革出現了切分軋制、熱軋冷拔 2
1.2.3 軋機結構改造 提高軋制速度 2
1.2.4 加熱爐控制 2
1.2.5 冷卻工藝改造 2
1.3 剪切機的種類和用途 2
1.3.1 擺動式剪切機 2
1.3.2 滾動式飛剪 2
1.3.3 曲柄偏心式飛剪 3
1.4 擺動剪研究的內容和方法 3
1.4.1 擺動剪在型鋼連續機組布置和作用 3
1.4.2 型鋼熱連軋機的生產工藝 3
1.4.3 擺動剪的結構特點和研究的內容與方法 4
2 擺動剪設計方案的選擇和評述 5
2.1 擺動式剪切機設計方案的選擇 5
2.1.1 擺動式剪切機傳動簡圖 5
2.1.2 擺動剪的剪切過程 5
2.2 擺動剪設計方案評述 5
2.2.1 減小擺角 6
2.2.2 增加許用擺角 6
3 剪切力的計算 8
3.1 剪切速度和剪切力 8
3.1.1 擺動剪設計參數 8
3.1.2 剪切機構主要參數的確定 8
3.1.3 剪切速度的確定 9
3.1.4 剪切力的計算 11
3.2 剪切力矩的計算 12
4 電機型號及容量的選擇 14
5 主要零件的強度計算 16
5.1 齒輪的強度計算 16
5.1.1 按齒面接觸強度設計 16
5.1.2 計算 17
5.1.3 按齒根彎曲強度設計 18
5.1.4 幾何尺寸計算 19
5.2 曲軸的強度計算 19
5.2.1 曲軸的尺寸和材料性能 19
5.2.2曲軸的強度校核 20
5.3 切向鍵的計算 21
5.4 滑塊損壞的改進設計 23
6 試車方法和對控制系統的要求 24
6.1 試車要求 24
6.2 維護規程 24
7 設備的可靠性及經濟分析 25
專題 潤滑方法選擇的探討 26
1 摩擦和潤滑的概念 26
2 液體潤滑和半固體潤滑比較 27
3 剪切機設備潤滑方法 27
結論 29
致謝 30
參考文獻 31
附錄 32