論文標準WORD格式排版 29頁 附裝配圖.dwg 行腔.dwg 推料桿.dwg 推件桿.dwg 水道.dwg 手機充電器外殼.dwg 模架.dwg 冷料穴.dwg 回程桿.dwg 導柱.dwg 導套.dwg



摘要

這套設計共花我4周的時間從圖書館查資料、和同學們討論、分析和整理成文，決定做手機充電器外殼的設計。設計中從材料的選取，工藝分析等來設計的。另外該套模具巧妙的設計了拉料桿，保證了凝料在第一次分型時留在凹模板一側，頂桿推動推桿固定板時凝料自動脫落，實現了從泣射到塑件被頂出的全自動化，提高了生產效率?；瑝K上的導軌既起導向功能，出便于安裝在凸模板上。由于塑件是壁厚較薄而均勻的塑件，而且，凸模部分有許多孔和凸臺，有較大的包緊力，為保正塑件的推出，故設計了多根推桿水平衡推出力。經過生產實踐證明，該副模具的開合模動作完全符合設計要求，適于大批量生產。

關鍵詞：分流道、注射、模具



Abstract

This nested design altogether spends I 4 week-long time to look up the material from the library, and schoolmates discusses, analyzes and reorganizes the article, decides the executor machine battery charger outer covering the design. In the design from the material selection, the process study and so on designs. Moreover this set of mold ingenious design has pulled the material pole, had guaranteed congeals the material when the first minute kept concave template one side, the roof bar impelled when the throwout lever dead plate congeals the material to fall off automatically, realizes from has sobbed shoots models the entire automation which went against, raised the production efficiency. On the slide guide rail already has the guidance function, leavesisadvantageous installs on the raised template. Because models is wall thickness is thin andevenmodels, moreover, the plunger part has permits porous and the lug boss, has big BaoJinthestrength, to guarantee is modelling extrusion, therefore designed many throwout leverlevelbalances to promote the strength. Proved after the production practice that this mold opensthematched molds movement to meet the design requirements completely, is suitable for the production in enormous quantities.



Key word: Minute flow channel, injection, mold



目錄

引言……………………………………………………………………………………...1

1、塑件工藝分析………………………………………………………………………...2

1.1 塑件設計要求………………………………………………………………………2

1.2 塑件生產批量要求…………………………………………………………………2

1.3 塑件的成型要求……………………………………………………………………2

1.4丙烯腈-丁二烯-苯乙烯共聚物（ABS）………………………...................................3

1.5材料的確定及相關參數……………………………………………………………..4

2、基本結構……………………………………………………………………………...6

2.1模具的成形方法……………………………………………………………………..6

2.2、型腔的布置…………………………………………………………………………6

2.3 選擇澆注系統………………………………………………………………………7

2.4 冷卻系統的設計…………………………………………………………………..9

2.5確定推出方式………………………………………………………………………11

2.6側向抽芯機構……………………………………………………............................12

2.7模具的結構形式…………………………………………………............................12

3、模具設計的有關計算……………………………………………............................13

3.1注射機的選擇………………………………………………………………………13

3.2、模具成形尺寸設計計算………………………………………………………….13

4、注塑機參數校核…………………………………………………………………….15

4.1最大注射量校核…………………………………………………………………...15

4.2 鎖模力校核…………………………………………………………......................15

4.3 模具與注塑機安裝部分相關尺寸校核…………………………………………..16

4.4 模具閉合高度校核………………………………………………………………..16

4.5 開模行程校核……………………………………………………………………..16

4.6模具結構、尺寸的設計計算………………………………………………………16

4.7型腔結構……………………………………………………………………………16

4.8型芯結構……………………………………………………………………………18

4.9導向機構……………………………………………………………………………18

4.10復位桿……………………………………………………………………………..19

4.11拉料桿……………………………………………………………………………..20

4.12推件桿……………………………………………………………………………..21

4.13推出結構…………………………………………………………………………..22

5、塑料注射模具技術要求及總裝技術要求…………………………………………24

5.1零件的技術要求……………………………………………………………………24

5.2總裝技術要求及裝配圖……………………………………………………………24

參考文獻…………..