畢業論文標準WORD格式排版 36頁 附機械總裝圖.dwg 軸耳.dwg 油箱.dwg 液壓原理圖.dwg 下板.dwg 外連桿.dwg 上板架.dwg 內連桿.dwg 焊接件.dwg 固定鉸接處.dwg 閥體.dwg 閥塊.dwg 泵站圖.dwg

摘 要
本次畢業設計對象是液壓升降平臺，這套裝置主要用于舉升重物。它的舉升高度為1米，舉升重量為1噸，其動作主要是由兩個雙作用液壓缸推動“X”型架，帶動上板來實現的。該液壓升降平臺主要由兩個部分組成：機械部分和液壓部分，其中機械部分主要由上板架、下板架、內連桿和外連桿四部分組成。本設計設計、選擇了機械部分材料與結構，并對其進行受理分析與校核，以便檢驗是否滿足強度、剛度的要求，分析及校核的結果證明機械結構的設計可以滿足要求。在對液壓控制系統的設計過程中，先進行了總體方案設計。在選擇液壓的各個控制回路的時候，在對各個回路進行了對比后調速回路我選擇了進油口節流調速回路；卸荷回路我選擇了帶有二位二通電磁換向閥的卸荷回路；保壓回路我選擇的是用液控單向閥的保壓回路。確定了各種基本回路后，又確定了液壓系統的傳動形式，由于開式系統所具有的系統簡單和散熱條件好等優點，所以把傳動系統確定為開式系統。在擬定液壓系統原理圖后，對液壓元件及輔件進行了設計、選擇，并對其進行校核。經過計算后液壓缸選定為45毫米的液壓缸，液壓泵選定為齒輪泵，根據系統工作的最大功率我選擇的電動機為Y112M-4行三相異步電動機。在確定泵后，又對其他的元件及輔件進行了合理的選擇，最后確定各種元件后,進一步完成了我的設計題目。

關鍵詞: 液壓；升降平臺；上板架；下板架；內連桿；外連桿

Abstract
I graduated from the current design is done mainly hydraulic lifts, mainly divided into two parts: mechanical and hydraulic parts. Mechanical parts which I think the main needs to be considered is the subject of several major part of the intensity: on board planes, under the board planes, within and outside link connecting rod. In this part of my four were on board from top to bottom-line Analysis of the internal and external linkage, I had the strength check. After my analysis and after checking I think I can satisfy the design requirements. Then I entered the various parts of the hydraulic choice. In the choice of the hydraulic control circuit all the time, in the loop on a comparison of the governor after I selected the import speed loop circuit; unloading loop I chose the valve of the unloading circuit; packing circuit I have chosen The use of one-way valve controlling the packing circuit. In determining the needs of the various circuit I, I'm sure I wear the hydraulic system of fixed form, according to open-system and the system simple cooling system features good condition, I set my drive system for open - System. On the other hydraulic components accessories choice, I had to them after the calculation of the hydraulic cylinders after I voted 45 mm of hydraulic cylinders, according to the transmission gear pump stability, I take my pump as a gear Pump, according to my system the maximum power of the work I elected to the motor Y112M-4 to three-phase asynchronous motor. I set the pump, I also based on this I need the yuan other accessories for a reasonable Choose, finally, I identified a variety of components, further complete the design of the topics I.

Keywords：Mechanical;Hydraulic; Panels from top to bottom;Inside and outside link

目錄
摘 要I
AbstractII
第1章 緒論1
第2章 確定液壓系統方案2
2.1確定基本回路2
2.1.1卸荷回路2
2.1.2 調速回路的確定4
2.1.3保壓回路的確定7
2.2 液壓傳動系統的形式確定9
2．3 液壓系統原理圖10
第3章 設計、選擇液壓元件、輔件11
3.1確定液壓缸系數11
3.1.1 初選系統壓力11
3.2 液壓輔助元件的計算及選擇12
3.3油箱的設計12
3.3.1油箱的設計要點13
3.3.2油箱容積計算13
3.4 其它元、輔件的選擇13
3.4.1.吸油濾油器13
3.4.2選擇濾油器的基本要求14
3.4.3溢流閥的選擇14
3.4.4壓力表開關選擇14
3.4.5單向節流閥15
3.4.6液控單向閥的選擇15
3.5閥塊的設計15
3.6 效率的計算16
3.6.1計算沿程壓力損失16
3.6.2效率計算18
3.6.3系統發熱與溫升計算19
3.6.4液壓系統的一般使用和維護19
第4章 機械部分的受力分析力22
第5章 機械部分的強度校核25
5.1 外連桿強度校核25
5.2 內連桿強度較核26
5.3 連接兩連桿的銷軸的強度校核27
第6章 結論29
參考文獻30
致謝31