畢業論文標準WORD格式排版 73頁

摘 要
本次畢業設計是關于普通型膠帶輸送機選型的設計。首先對膠帶輸送機作了簡單的介紹；接著分析了膠帶輸送機的選型原則及計算公式；然后按照這些設計準則設計了符合本次設計要求的大傾角下行運輸?shù)哪z帶輸送機；接著對所選擇的輸送機各主要零部件進行了校核。同普通膠帶輸送機一樣，大傾角下行運輸膠帶輸送機也是有六個主要部件組成：傳動裝置，機尾或?qū)Щ匮b置，中部機架，拉緊裝置，以及膠帶。唯一不同的是其膠帶上壓有花紋，用來增大膠帶工作表面的摩擦力，避免物料在速度突然變化時與膠帶之間產生滑移。最后簡單的說明了輸送機的安裝與維護?，F(xiàn)在，膠帶輸送機正朝著長距離，高速度，低摩擦的方向發展。近年來出現的氣墊式膠帶輸送機就是其中的一個。目前，在膠帶輸送機的設計、制造以及應用上，國內與國外先進水平相比仍有較大差距。國內在設計制造膠帶輸送機過程中存在著很大程度上的浪費。這個問題可以在校核尾架時發現。
本次設計代表了選型設計的一般過程。對機械的選型設計工作有一定的參考價值。

關鍵詞: 膠帶 傳動滾筒 托輥

Abstract
吀梔攀 design is a graduation project about the belt conveyor with a large dip. At first, it is introduction about the belt conveyor. Next, it is the principles about choose component parts of belt conveyor. After that the belt conveyor with a larger dip abase on the principle is designed. Then, it is checking computations about main component parts. Just as ordinary belt conveyor, the belt conveyor consists of six main parts: Drive Unit, Jib or Delivery End, Tail Ender Return End. Intermediate Structure, Loop Take-Up and Belt. The only different is it uses pattern belt, which used to increase friction to avoid the move between the belt and goods. At last, it is explanation about fix and safeguard of the belt conveyor. Today, long distance, high speed, low friction is the direction of belt conveyor’s development. Air cushion belt conveyor is one of them. At present, we still fall far short of abroad advanced technology in design, manufacture and using. There are a lot of wastes in the design of belt conveyor. This problem is discovered in the computations of the tail stand.

Keywords: belt driving roller roller

目 錄
1概述1
1.1帶式輸送機的發展?fàn)顩r1
1.2主要部件的結構及功能3
1.2.1錀送帶4
1.2.2堀詢6
1.2.3滾筒8
1.2.4焀動裝置：9
1.2.5拉緊裝置11
1.2.6清掃器11
1.2.7機架12
1.2.8導料槽13
1.2.9瘀荑13
2設計計算法則及主要公式15
2.1帶寬與速度的確定15
2.1.1帶寬15
2.1.2帶速的選擇16
2.2焀動形式的確定18
2.3運行阻力的計算18
2.3.1錀送帶運行阻力18
2.3.2曲線段運行阻力21
2.4錀送帶各點張力的計算24
2.4.1逐點張力計算法25
2.4.2錀送帶的懸垂度條件27
2.5錀送帶強度的驗算28
2.6傳動滾筒直徑的確定及強度的確定31
2.7拉緊裝置的計算35
2.7.1拉緊裝置的行程35
2.7.2拉緊力的計算36
2.8電動機和減速器的確定37
2.8.1電動機的功率37
2.8.2電動機轉子的變位質量38
2.8.3減速器的減速比39
2.9制動力與逆止力的計算39
2.9.1制動力的計算39
2.9.2電動機軸上的計算41
2.10琀羏葢壽命的計算41
3設計計算44
3.1設計依據：44
3.2主要參數的計算與部件確定45
3.2.1錀送帶帶速v及輸送帶寬度Ｂ的確定：45
3.2.2焀動形式的確定46
3.2.3運行阻力計算47
3.2.4錀運帶上各點張力計算：48
3.2.5錀送帶的強度驗算50
3.2.6傳動滾筒直徑的確定51
3.2.7拉緊裝置52
3.2.8機功率和減速器的減速比的計算53
3.2.9制動力的計算54
3.2.10瘀他部件計算：55
4電氣及安全保護裝置64
5操作規程與維護、保養65
5.1設備的正常使用65
5.2操作方面注意事項65
致 謝67
參考文獻68