畢業設計：S195柴油機機體三面精鏜組合機床總體設計及夾具設計
論文說明書共32頁，字?jǐn)?shù)總計：14372
資料簡介：
A0-夾具裝配圖.dwg
A0-零件工序圖.dwg
A1-夾具體.dwg
A3-端蓋2.dwg
A3-端蓋.dwg
A4-連桿.dwg
A4-密封圈.dwg
A4-手柄.dwg
A4-推程桿.dwg
A4-推桿.dwg
A4-軸套1.dwg
A4-軸套2.dwg
A4-注油嘴.dwg
畢業設計論文封面.doc
畢業設計說明書：S195柴油機機體三面精鏜組合機床總體設計及夾具設計.doc
附件清單.doc
任務書.doc
任務書封面.doc
說明書目錄.doc
摘要.doc
摘 要

夾具設計是機械制造廠里的一種工藝裝備，有機床夾具，焊接夾具，裝配夾具，檢驗夾具等，一般的機床夾具是作為機床的輔助機構設計的，而組合機床夾具是作為機床的主要組成部分，其設計工作是整個組合機床設計的重要部分之一。組合機床夾具應便于實現定位和夾壓的自動化，并有動作完成的檢查信號。夾具體在機床上的安裝都是通過夾具體上的安裝基面與機床上的相應表面的接觸或配合實現的。當夾具體在機床工作臺上安裝時，夾具的重心應盡量低，重心越高則支承面應力越大，夾具底面四邊應凸出，使其接觸良好，或底部設置四個支腳。當夾具體在機床主軸上安裝時，夾具安裝基面與主軸相應表面應有足夠的配合精度，并保證安裝穩定可靠。



關鍵詞: 夾具設計 組合機床 總體設計


Abstract
Tongs design is a kind of craft that machine manufactory in equip, organism bed tongs, welding tongs, assemble tongs, examination tongs etc., the general machine bed tongs is an assistance to be used as the machine bed organization design of, but the combination machine bed tongs is an importance to be used as the machine bed to constitute the part primarily, its design work is whole combination machine bed design part of a. Combination the machine bed tongs shoulds be easy to realize fixed position with clip the automation that press, also the check signal that action complete. The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.When the tongs installs in the machine bed work on the stage, the center of gravity of the tongs should be as far as possible low, center of gravity the more high an accepts should the dint is more big, the tongs bottom four directions should bulge, make its contact good, or the bottom establishes four a feets.When the tongs installs on the machine bed principal axis, the tongs install the to should have the enough match accuracy with principal axis cowgirl surface, and guarantee the gearing the stability dependable.



Keywords: tongs combination the machine bed clip the automation
目 錄
引言……………………………………………………………………………………1
1 工藝方案的擬定……………………………………………………………………3
2 定位基準及夾位點選擇……………………………………………………………3
3 組合機床總體設計——三圖一卡…………………………………………………6
3.1被加工零件工序圖…………………………………………………………………6
3.2加工示意圖…………………………………………………………………………6
3.3動力部件的選擇……………………………………………………………………9
3.4組合機床生產率的計算……………………………………………………………11
3.5機床聯系尺寸圖……………………………………………………………………14
4 夾具設計……………………………………………………………………………17
4.1設計步驟……………………………………………………………………………17
4.2 定位支承系統……………………………………………………………………17
4.3 定位誤差的分析計算……………………………………………………………17
5 導向裝置………………………………………………………………………………21
6 夾緊力的計算……………………………………………………………………22
7 夾緊機構……………………………………………………………………………24
7.1設計夾緊機構應滿足的要求………………………………………………………24
7.2夾緊氣缸………………………………………………………………………………25
7.3活塞桿的計算………………………………………………………………………25
8.夾具體設計…………………………………………………………………………27
8.1對夾具體的要求…………………………………………………………………27
8.2夾具體的技術要求…………………………………………………………………28
結 束 語……………………………………………………………………………28
致 謝………………………………………………………………………………29
參考文獻………………………………………………………………………………30
附件清單………………………………………………………………………………31