煤氣警報器設計

摘  要

當今社會上，出現了許多煤氣報警器，而這些產品大都是針對煤氣的泄漏所做出的相應的報警，即為家庭式煤氣報警器。本課題設計煤氣報警采用了AT89S52單片機為報警器的核心部件，對煤氣報警器進行控制。通過NAP-505電化學一氧化碳氣體傳感器對煤氣進行檢測，將所得的濃度值與設定濃度值相比較得到偏差。通過對偏差信號的處理獲得控制信號，發生報警信號，并把報警通道顯示并儲存在DS12887的RAM中，八個單元的煤氣濃度對應模擬量利用A/D轉換為數字量，并加入了鍵盤輸入控制，從而實現對家用和工業煤氣漏氣的監控。整個系統的硬件電路設計合理，性能安全可靠。

關鍵詞：單片機 煤氣濃度 報警器
 

Design of the coal gas’ alarm device

ABSTRACT

There are many coal gas alarm’s devices in our lives. These devices will alarm after the coal gas leaking. We call them household or industy appliances. This paper introduces the design of a coal gas alarm’s device that use the AT89S52 SCM as the most important controller. It is a core-components that control the whole programs and circuit of the coal gas alarm’ device. The appliance monitors the density of coal gas with the sensor of NAP-505 and compares the current density with the setting density. We get the control signal through the dealing with the deviation signal and then sent a alarm signal that is memoried in a RAM of DS12887. The analog signal of eight densities of the coal gas are transformed into the digital signal with the A/D converter, in addition which is cotrolled with the keyboard. We can monitor the leak of coal gas in the house or industy. The hardware design of circuits is reasonable and the performance of the coal gas alarm’s device is safe and reliable.
   
Keywords: SCM  Density  Alarm’ device

目  錄
摘  要 I
ABSTRACT II
1  前言 1
1.1研究背景 1
1.2研究意義 2
1.3研究內容 2
2  系統總體設計 3
2.1方案的選擇 3
2.2系統流程框圖 3
3  硬件系統設計與傳感器選用 4
3.1主機部分 4
3.1.1AT89S52單片機 4
3.1.2DS12887實時時鐘芯片及其電路 6
3.1.3X5045看門狗定時器及復位電路 8
3.1.4 電源電路 9
3.2功能模塊部分 9
3.2.1TLC2543的數據采集單元 10
3.2.2HD7279的人機接口電路模塊 12
3.2.3數據處理模塊 15
3.2.4聲光報警模塊 16
3.2.5ISP下載電路DIY 17
3.3傳感器的選用 18
3.3.1NAP-505型電化學式傳感器 19
3.3.2MQ-9半導體氣體傳感器 20
3.4硬件設計小結 22
4  軟件設計 23
4.1主程序設計 23
4.1.1初始化程序和主程序 23
4.1.2中斷服務程序 27
4.2功能實現主要子程序 28
4.2.1采集程序 28
4.2.2數據處理模塊 30
4.2.3報警記錄和報警模塊 31
4.2.4人機對話子程序設計 31
4.3小結 34
5  系統調試與分析 35
5.1硬件焊接與調試 35
5.2軟件調試 36
5.3系統調試 38
5.4小結 39
參考文獻 40
附  錄1 程序源代碼 41
附  錄2 焊接實物圖 56
附  錄3 元器件清單 58
謝  辭 60