摘 要

本論文研究的是汽車操縱穩定性轉向回正性試驗數據處理研究。汽車的轉向回正性是評價汽車操縱穩定性的一個重要指標。一輛沒有回正能力的汽車,或基本上回不到正中(即有較大的殘余橫擺角速度)、或回正過程中行駛方向往復擺動的汽車,都是令人不滿意的。為了提高汽車的操縱穩定性，就必須使汽車的轉向回正性能優越，才能提高汽車的整體性能。由于操縱穩定性轉向回正試驗測試結果數據繁多，數據處理過程復雜，如果僅靠人工利用現有通用軟件進行數據處理，不僅耗費大量的人力和時間，而且很難使處理結果規范統一。數據處理大大加重了試驗人員的工作負擔，因此需要開發專門的軟件對操縱穩定性的試驗數據進行快速統一的處理，獲得滿足測試報告所需的準確規范的數據處理結果。我們根據國家標準GB/T 6323.4-94《汽車操縱穩定性試驗方法轉向回正性能試驗》，分析試驗所需要記錄的數據及試驗數據處理要求，提出試驗數據的自動處理方案，采用delphi7開發試驗數據自動處理軟件，為汽車的轉向回正性能數據處理提供方便。本課題采用delphi7編寫程序 ，使達到如下功能：待處理數據輸入、結果數據輸出；按照標準進行數據處理和試驗評價；原始數據的圖形顯示及截取；試驗報告自動生成。


關鍵詞：汽車轉向回正性，自動處理軟件，delphi7














ABSTRACT

This paper is on the stability of vehicle Steering Wheel Returnability tentative test data processing.The returnability tentative is an important indicator to the eva luation of the stability of vehicle operation. It is unsatisfactory if an automobile without returnability, or basically back to less than the median （i.e. a greater residual swaying angular velocity, or in the direction of reciprocation swinging on the automobile during the returnability process. In order to improve automobile operation stability, we must make the returnability tentative superior, which can improve the car's overall performance. Because of the numerous test data and the complex data processing in the stability of vehicle operation and returnability tentative test, if we only depend on the manual use of existing general software for data prcessing that may cause not only massive manpower and time consumption but the difficulty to standardize the results of reunification. The data processing aggravated the work burden greatly, therefore we need to develop a specialized software to handle the fast unification processing of the stability of vehicle operation test data; then meet the accurate standardized data-processing results for required test report. According to the national standards GB / T 6323.4-94 “Automobile Operation Stability Test Method and Returnability Tentative Test ”，we analyzes the data which need to be record and the request of data processing request, proposed an automatic data processing programmes, uses the delphi7 development automatic processing software, providing convenience for returnability tentative test data processing. This topic uses delphi7 written program to achieve the following functions: to deal with data input and data results output; to be in accordance with the standards for data processing and test eva luation; raw data graphics and interception; automatically generated test report.


Key words： Steering Wheel Returnability, automatic processing software, delphi7








目 錄

中文摘要 Ⅰ
ABSTRACT Ⅱ
1緒論 1
1.1 汽車的轉向回正性能 1
1.1.1汽車操縱穩定性概述 1
1.1.2汽車操縱穩定性的客觀試驗 1
1.1.3轉向回正性的概念 1
1.1.4轉向回正試驗 1
1.2課題的提出 2
1.3汽車轉向回正性能試驗數據自動處理系統 3
1.4本論文所作工作 3
2轉向回正性能試驗方法及標準 5
2.1轉向回正性研究及評價 5
2.1.1轉向回正性的研究 5
2.1.2試驗的評價方法 5
2.2轉向回正性的試驗標準GB/T 6323.4-94 6
2.2.1測量變量 6
2.2.2試驗條件 6
2.2.3試驗方法 7
2.2.4試驗我據處理與結果表達 7
2.3汽車操縱穩定性指標限值與評價方法QC/T480-1999 10
3汽車轉向回正性自動處理軟件設計分析 12
3.1開發工具的選擇 12
3.1.1 Delphi介紹 12
3.1.2 Delphi7的特點 12
3.2系統應用需求分析 12
3.3系統功能結構框架圖 13
3.4系統功能 14
3.4.1試驗數據輸入 14
3.4.2歷史試驗數據的處理 14
3.4.3查看低速圖形和高速圖形 14
3.4.4快速生成試驗報告書功能 14
4應用軟件設計 15
4.1系統的界面設計 15
4.1.1歡迎窗體的設計 15
4.1.2轉向回正數據處理窗體 15
4.2代碼設計 17
4.2.1導入數據設計 17
4.2.2截取數據設計 19
4.2.3數據計算設計 20
4.2.4結果評分設計 20
4.2.5查看圖形設計 21
4.2.6生成報告設計 22
4.3數據格式 23
5轉向回正性數據自動處理軟件 25
5.1應用軟件的實現功能 25
5.1.1導入低速和高速數據 25
5.1.2數據選取 26
5.1.3截取數據 27
5.1.4數據計算 28
5.1.5結果評分 28
5.1.6后續步驟 29
5.2本章小節 31
6 結論 32
6.1課題介紹 32
6.2總結 32
致 謝 34
參考文獻 35